How to flash Firmware on DMA Card 35T

All software setup/installation is done on the second computer that is connected to the DMA card by way of USB. DO NOT install/setup this software into the main computer in which you installed the DMA card into the motherboard's PCIe slot. Installing files onto the wrong computer may result in detection.

1. Turn off the Main PC and install the DMA Card in PCI express slot (x1, x4 or x16) of your motherboard

2. Insert USB 3.0 cable into the JTAG port of your DMA card

3. Insert the other side of USB cable into a USB 3.0 port on the Second PC

4. Turn on Main and Second PC

5. Go to folder 2. Flashing tools and run Zadig.exe as administrator

6. Click Options >> List All Devices

7. You will see several devices, among which there will be RS232-HS (Interface 0, 1, 2 and 3)

8. First select Quad RS232-HS (Interface 0) and click on big button "Replace Driver". Wait for installing the driver

9. Then select RS232-HS (Interface 1) and click on big button "Replace Driver". Wait for installing the driver

10. Then select RS232-HS (Interface 2) and click on big button "Replace Driver". Wait for installing the driver

11. Then select RS232-HS (Interface 3) and click on big button "Replace Driver". Wait for installing the driver

12. Change name of your firmware .bin file to: pcileech_screamer_m2_top

13. Move you firmware file (pcileech_screamer_m2_top.bin) to the folder 2. Flashing tools

14. Go to the folder 2. Flashing tools and run "flash" file

15. You should see process of flashing, which will take about 2 minutes

16. After the process is completed, turn off your Main PC and Second PC and turn off the power (switch on the power supply to position "0" or pull the power supply cable out of the socket) for 30 seconds

This is a mandatory step, don't ignore it

turn off the main PC's power supply after flashing firmware for dma card 35t

17. Connect USB cable to the DATA port on the DMA card and turn on your Main and Second PC

18*. If you have full emulated firmware from dma-cheats.com, go to folder 5. If you have full emulated firmware and follow the manual. You will receive a password from this folder from the manager when you purchase our firmware.

If you have not full emulated firmware, you don't need to follow this step.
If you bought a full firmware emulation anywhere other than dma-cheats.com, you don't need to follow this step either.

19. Go to the folder 4. DMA test\Full test\lone dma test

Run lone-dma-test.exe

Select 1. Full Test

< 60 MB/s — bad speed, you need to get a better USB Cable or try another USB 3 Port or another PCIe slot

>= 100 MB/s — good speed

>= 150 MB/s — great speed

If the test was failed, watch the video and read the troubleshooting below

Video Manual

Firmware Installer error

Firmware Installer Error

Make sure that you:

Using DMA card with 35T chip (we sell only DMA cards with 35T chip)
We have completed the BIOS setup
Using Windows 10 on both PC
Connected USB cable to JTAG (CFG) port of DMA card and to second PC USB 3.0 port
Launching JTAG Firmware Installer on Second PC
Moved JTAG Firmware Installer to desktop
Moved firmware file (.bin) to desktop
If you are using a third-party DMA card, try using another Tool from the folder "6. If you have another DMA card".

Bad Test / Slow Speed

Bad Test / Slow Speeds

If speed test was failed:

Turn off Gaming-PC and unplug the power cord.
Unplug the DMA-USB from Radar-PC.
Press and hold the Gaming-PC power button for 15 seconds to unload any residual voltage.
Plug DMA - USB back into Radar - PC and reconnect the Gaming - PC power cord.
Power up the Gaming - PC.
Run Benchmark Tool and see if issues persist.

If speed test is slow:

~35-60 MB/s -> Make sure that you are on a USB 3.x cable and port

We recommend getting at least a 10gbit/s USB cable
Try different USB Ports on the second PC.
Usually USB 3.x ports are colored blue/red/orange/purple
USB 3.x ports usually have these icons next to them

~16-35 MB/s -> Most likely stuck in tiny algo

Try different PCIe ports and make sure that the BIOS settings are correct
If nothing else works try setting the pcie slot to gen3 / gen4 in bios.

Driver Installation Error

If certain peripherals not responding or behaving unusual or display is unresponsive/showing artefacts or behaving unusual:

Try different PCIe slots

DMA Failed to Connect

Check your USB cable
Open device manager on second PC
Search for FTDI Driver on USB category

Open folder DMA Cheats\2. Firmware\4. Driver for DMA Card
Find the driver you need
Right Click FTDI SuperSpeed-FIFO Bridge in device manager
Update Drivers with the extracted FTD3XX Drivers.
Make sure Second PC is fully updated and there are no windows updates pending
Check to make sure you are using a fast USB slot (cycle slots if necessary)

Where to download?

You will receive all the files necessary to set up a DMA card, Firmware, Kmbox, Fuser and our cheats when you purchase any product on our website (even if buy only cheat subscription for 40$, you will get ALL the files for DMA devices as well).

Firmware file (.bin) is unique and is developed for each customer individually, you can buy it here —

https://www.dma-cheats.com/firmware

You can also buy access to all the files for $5 — https://dmacheats.mysellix.io/product/access-to-dma-cheats-folder

Payment on the site is accepted using cryptocurrency. If you want to pay with a Binance Gift Cards, which you can buy using Credit Card, Apple Pay, PayPal — contact the Manager

tools, drivers for dma card, firmware, kmbox, fuser, dma cheats, xim matrix

See all Products →